Battery Detector, LCD6

SKU: LCD6

More Info

English

Features

  • Use for RC models’ battery voltage diagnosis and measurement.
  • High precision display of unit cell voltage for 2-6cells Lixx packs or 4-18 cells Nixx packs
  • 57mmX32mm large LCD can display up to 6cells unit voltage & total voltage clearly & directly.
  • Reverse polarity protection

Specifications

  • Use for 2~6 cells Lipo/Li-ion/LiMn
  • Voltage display resolution: 0.01V.  Voltage detection precision: 10mv
  • Unit voltage display range: 3.00~4.50V,
  • Total voltage display range: 4.80~27.00V
  • Current loading of test: <10mA
  • Pins distance: 2.54mm
  • Size: 81x45x10mm,   Weight: 32g

Instructions

  • Input total voltage should be 4.80V~27.00V. If the total voltage is under 4.80V, there is no display on the LCD. If the unit voltage is above 27.00V. it will hurt the LCD6.
  • For Lixx packs: Connect the LCD6 to the battery’s balance adapter , and attention the anode & cathode.  If the polarity is reversed. no display on the LCD screen.  If the battery is below 6 cells, pls connect the balance adapter from the cathode side.  If the LCD6 detect right input, LCD screen will display total voltage and unit voltage. From the Left-up to the right-down, unit voltage is the 1st to 6th.
  • For Nixx packs: Connect the LCD6 to the battery’s output cable. After the LCD-6 detect right input, LCD screen will display total voltage.
中文

特点:

  • 适用于遥控模型动力电池和接收电池的电压测量;
  • 准确显示2~6 cells 锂电池单元电压和总电压 或4~18 cells镍氢/镍镉总电压;
  • 57mmX32mm大屏幕LCD,能够一屏清晰直观的显示出最多6片单元电压和总电压;
  • 反接保护。

参数:

  • 适用于2~6cells的Lipo/Li-ion/LiMn,4~18 cells Nixx;
  • LCD电压显示精度:0.01V;电压测量精度:10mv;
  • 单元电压显示范围:3.00~4.50V,总电压显示范围:4.80~27.00V;
  • 测量时耗电电流:<10mA
  • 插针间距:2.54mm
  • 尺寸:81x45x10mm;重量:32g

使用说明:

  • 待测电池总电压不得低于4.80V或者高于27V,低于4.80V,屏幕不显示,高于27V,可能导致LCD-6损毁。Li电池单元电压不得低于3.00V。
  • Lixx电池测量:把Li电池的平衡头插入LCD-6左侧的Li平衡口,注意正负。
  1. 如果反插,LCD-6有反接保护,屏幕无显示。
  2. 低于6cells的电池,从LCD-6平衡口的负极开始插。
  3. 电池接入后,屏幕显示总电压,单元电压。
  4. 单元电压从左上-右下依次为第1,2,3,4,5,6片的电压。
  • Nixx电池测量:把Ni电池的输出线插入LCD-6左侧的Ni电检测口。
  1. 电池接入后,屏幕上端显示电池组总电压。
  2. 如电池组电压低于4.80V,则液晶不能工作。